Learn more
Standard French Door Unit Print
Overall Skill Level: Intermediate

Screen track and screen door installation instructions for a French door unit with 4-9/16" or 6-9/16" frame.
Steps
  1. Standard French Door Unit
    1. Cut tracks
    2. Modify tracks
    3. Drill tracks
    4. Install tracks
    5. Remove excess pile
    6. Install screen door
    7. Install handle set
    8. Adjust roller height
    9. Installation complete
Tools
  • Flat Head Screwdriver
  • Fine-Tooth Hack Saw
  • Tape Measure
  • Pencil
  • 5/32" Drill Bit
  • Drill
  • Utility Knife
Materials
  • (2) Screen Doors
  • (2) Screen Tracks
  • (2) 2-Part Screen Door Handles
  • (12) 1" Panhead Screws
  • (4) 3/4" Black Screws
  • (2) 5/16" Black Screw
Standard French Door Unit
Skill Level: Intermediate
  1. Cut tracks
    For door units with a 4-9/16" frame: Measure, mark and cut one track at 72-1/2", and the other at 71-1/2". Use a fine tooth hack saw to cut tracks.
    For door units with a 6-9/16" frame: Measure, mark and cut both tracks at 71-1/2". Use a fine tooth hack saw to cut tracks.
  2. Modify tracks
    For door units with a 4-9/16" frame: Modify only the 71-1/2" track.
    For door units with a 6-9/16" frame: Modify both 71-1/2" tracks.
    Using a utility knife, score along the grooves on both sides of the 71-1/2" tracks. Carefully bend the top 2 legs back and forth until they can be removed. The remaining track will look like an "M".
  3. Drill tracks
    Using a 5/32" drill bit, drill a hole 4" from the end of each track (one hole above the raised guide track, and one below). Drill 4 more holes evenly spaced between the 2 original holes, for a total of 6 holes per track. Repeat for both tracks.
  4. Install tracks
    For door units with a 4-9/16" frame: Mount the 72-1/2" track directly under the brickmould using 6 qty., 1" panhead screws through the holes you have drilled. Once the 72-1/2" track is mounted, mount the 71-1/2" track behind the first track, flush with the front edge of the head jamb. (See Figure 5a)
    For door units with a 6-9/16" frame: Mount the first track, 2" in from the front edge of the door jamb using 6 qty., 1" panhead screws through the holes you have drilled. Mount the second track 1/4" in front of the first track. (See Figure 5b)
  5. Remove excess pile
    Remove excess pile (fuzzy strip) from the top and bottom of the screen doors.
  6. Install screen door
    Install the screen door on the inactive side of the main door first (door with astragal). Install the screen with the handle holes positioned towards the side jamb, the spring-loaded wheels facing up and the fuzzy strip facing the main door. Tip the top of the screen into the top track closest to the main door, and then lift the bottom of the screen onto the raised guide on the aluminum sill. Repeat this process for the outer screen, positioning the handle holes toward the opposite jamb. NOTE: Both fuzzy strips should point toward the main doors.
  7. Install handle set
    Install the handle set for the screen doors by snapping the two halves of the handle together (thicker half to the inside of the screen door) in place over the pre-drilled holes, with the handles pointing towards the center of the doors. Secure with 2 qty., 3/4" black screws and one 5/16" black screw. Repeat on second screen door.
  8. Adjust roller height
    Complete installation by adjusting the height of the rollers on the bottom of the screen doors (approximately 1/8" above sill) until the screen travels smoothly across the aluminum sill. Turn the screw clockwise to raise the screen, and counterclockwise to lower it. Each screen door has an adjustment screw at both bottom corners, for a total of 4 points that will need adjustment.
  9. Installation complete
    Your properly installed Mastercraft Screen Door should provide years of trouble-free service.
Products, materials, techniques, tools, building codes and local regulations are subject to change; therefore, Midwest Manufacturing assumes no liability for omissions, errors or the outcome of any project. The reader must always exercise reasonable caution, follow current codes and regulations that may apply, and is urged to consult with a licensed professional before beginning any project.